Skip to content

RCBS .308 Small Base Dies: Setup, Use, and Selection Guide

By Published 7 min read

As an Amazon Associate we earn from qualifying purchases, at no cost to you.

On this page (7 sections)
  1. What Small Base Dies Actually Do
  2. When You Actually Need a Small Base Die
  3. How to Set the RCBS Small Base Die
  4. Common Myths About Small Base Dies
  5. How to Choose the Right Die Set
  6. The bottom line
  7. Frequently asked questions

Your .308 rounds jam in a semi-auto rifle, or you are starting a new case batch and want to ensure they chamber every time. This page explains what RCBS small base dies do differently and how to set them for your specific firearm.

In short: RCBS small base dies size the case head area smaller than standard full-length dies to ensure reliable feeding in tight semi-automatic chambers. You use them when standard dies leave cases too loose or when you want to extend case life by reducing stretching. Set the die to just contact the case head, not the shoulder, for best results.

Quick picks

Our shortlist for this job · tap one to see today's price
Best for .308 semi-auto loadersRCBS Small Base Die Set .308 Win

Includes the small base sizer and bullet seater needed to fix tight chamber issues in your rifle.

Check price on Amazon
Alternative for case life extensionRCBS X-Die FL Die Set .308 Win

X-Die design reduces case stretching more than small base dies if your main goal is longevity.

Check price on Amazon

What Small Base Dies Actually Do

RCBS .308 Small Base Dies: Setup, Use, and Selection Guide

Standard full-length dies resize the entire case, including the shoulder and headspace. Small base dies only resize the case head, the back part of the brass. This keeps the shoulder untouched while ensuring the head fits tight in the chamber. For the detail, see our notes on right reloading guide.

For .308 Winchester, chamber tolerances can vary between rifles. Some are tight. If your case head is oversized after firing, it may not feed reliably in a semi-auto. The small base die fixes this specific gap without resizing the whole case.

RCBS designs these dies to size the head slightly smaller than factory specifications. This creates a tight fit that prevents head-to-head jamming in magazines. The process is mechanical and consistent, relying on the die’s internal taper to compress the head uniformly.

Recommended for this stepRCBS Small Base Die Set .308 Win

This two-piece set gives you the small base sizer and bullet seater needed to implement this change in your press.

  • Sizes cases slightly smaller for dependable chambering.
  • Works well for firearms with tighter chambers.
Check price on Amazon

When You Actually Need a Small Base Die

You do not need a small base die for every .308 round. Use it when you face specific problems with your rifle or brass:

  • Tight Chamber Semi-Autos: If your M14, FNF2000, or similar rifle jams on the second round, your case heads are likely too large. Small base dies fix this by compressing the head diameter. This is critical for military-spec rifles that have tighter tolerances than commercial bolt guns.
  • Old Military Brass: Some older .308 brass has large heads that won’t chamber in modern tight rifles. These dies recover that brass by reducing the head diameter back into usable range. This allows you to fire brass that would otherwise be useless or discarded.
  • Case Life Extension: By not resizing the shoulder every time, you reduce metal working on the weakest part of the case. This extends life slightly compared to full-length resizing every shot. However, the head still undergoes stress every cycle, so it is not a permanent fix for failing brass.

If your bolt-action rifle feeds fine and your cases look normal, a standard full-length die is simpler and usually sufficient. Do not force small base dies into a workflow where they are not needed, as they require more attention to headspace settings.

Pro tip: Check your chamber with a gauge before buying. If your chamber is standard, you may only need small base dies for specific old brass lots.

How to Set the RCBS Small Base Die

How to Set the RCBS Small Base Die

Setting a small base die is different from a standard die. You are not trying to take up headspace; you are trying to size the head. The goal is to make the head fit snugly in the chamber without binding. The other half of this decision is seating 30-06 bullets with dies.

If you set it too tight, you risk head separation or difficulty in extraction. If you set it too loose, you will continue to have feeding issues. We go through die brand comparison step by step in its own article.

  1. Screw the die down until it just contacts the case head. Do not crush the case. The resistance should be firm but manageable without excessive force.
  2. Check for resistance. It should feel like you are moving against light tension, not fighting a block. The die’s small base section should compress the brass slightly.
  3. Resize a fired case. Run a previously fired case through the die. It should look uniform and have no dents or irregularities. The head should be smooth.
  4. Test chambering. Attempt to chamber the resized case. It should slide in smoothly. If it binds, back the die out. If it drops out too easily, lower it slightly.

If the case is too tight to feed, back the die out slightly. If it is loose, lower it a little more. Always check a few cases from different lots, as brass thickness can vary. Record your die setting for consistency in future reloading sessions.

Common Myths About Small Base Dies

Myth: Small base dies are for all .308 rifles.

Fact: They are primarily for semi-automatics with tight chambers or specific brass types. Bolt-action rifles usually use standard dies because their chambers are looser and they do not rely on magazine feeding for the next round.

Myth: They make your cases last forever.

Fact: They extend case life by reducing shoulder wear, but the head still works every time. The head area is subject to pressure every shot. Cases will eventually crack, split, or stretch beyond limits. Small base dies slow down the process but do not stop metal fatigue.

Myth: You can ignore case length.

Fact: Even with small base dies, you must check overall length (OAL) periodically. If the case stretches past the maximum safe length for your rifle, it can cause pressure issues. Trim cases as needed. The small base die does not control the shoulder, so the case length is still determined by the fire event and any trimming you perform.

Myth: They are harder to use than standard dies.

Fact: They require more precise setup. Once set, the workflow is similar. The extra step is verifying the head fit regularly, especially when switching brass lots. With practice, it becomes second nature.

Recommended for this stepRCBS X-Die FL Die Set .308 Win

If you are still unsure if small base is enough, an X-Die set offers more comprehensive case life extension.

  • Die Full-Length Die Set .308 Win: Extended case life reloading die set designed for
  • Fast Decapping: Designed for .30 caliber cases, this unit quickly and efficiently
Check price on Amazon

How to Choose the Right Die Set

RCBS offers different die types. Choose based on your specific need and the type of brass you are working with. Do not buy a small base set if you do not have a tight chamber rifle or large head brass; you are paying for complexity you do not need. Before you buy anything, it is worth looking at which die set fits your budget.

  • Standard 2-Die: Best for bolt-actions and most semi-autos with normal chambers. Simple and fast. It resizes the whole case in one motion. Good for high volume reloading where case life is secondary to speed.
  • Small Base 2-Die: Best for tight chamber semi-autos or recovering large-head brass. Fixes feeding issues. Use this if your rifle has a reputation for tight chambers or if you are using commercial surplus brass that is oversized.
  • X-Die 3-Die: Best for maximum case life. Separates decapping and sizing, reducing stretching. The X-Die system uses a flared die to decap, then a small base die to size the head, then a standard die to resize the shoulder. This three-step process works less metal per cycle, significantly extending case life. It is the premium choice for match shooters.

If you are starting fresh, a standard set is fine. Add small base dies only when you have a specific feeding problem or old brass to manage. Keep your dies clean and lubricated to ensure consistent sizing. Store them in a dry place to prevent rust.

The bottom line

Get RCBS small base .308 dies if your semi-auto rifle has tight chamber issues or you are working with old military brass that won't feed. Set them to just contact the case head. If you just want standard reloading, stick with a full-length die set.

Our top pickRCBS Small Base Die Set .308 Win
  • Sizes cases slightly smaller for dependable chambering.
  • Works well for firearms with tighter chambers.
Check price on Amazon

Frequently asked questions

Can I use small base dies in a bolt action rifle?

Yes, but it is rarely necessary. Bolt actions have looser chambers and do not rely on magazine feeding. Use small base dies only if you have specific case issues or want to extend life slightly. For most bolt guns, a standard die is sufficient and easier to manage.

What is the difference between RCBS small base and X-Die sets?

Small base dies size only the case head. X-Die sets separate decapping and sizing, which reduces case stretching overall. X-Dies are better for case life; small base dies are better for tight chamber feeding. You can use both in a three-step process for maximum longevity.

Do small base dies change the overall length of my case?

No. Small base dies should not change the overall length. They only size the head. If your OAL changes significantly, check your die setup or consider that your cases are stretching. The shoulder position is not affected by the small base die, so length is determined by the firing event.

How do I know if my .308 chamber is tight?

If you have head-to-head jams in a semi-auto magazine, your chamber is likely tight. You can also use a chamber gauge from a reputable maker to verify specifications. If the gauge goes in with resistance but fits, your chamber is within normal tolerances. If it does not fit, your chamber is very tight. There is more on low velocity 308 hunting viability in a separate guide.