Hornady 308 Subsonic: Can You Hunt With It?
By Amis Thains Published 5 min read
As an Amazon Associate we earn from qualifying purchases, at no cost to you.
On this page (7 sections)
You are trying to reduce noise or recoil in a .308 for close-range varmint work or ethical small-game hunting, but you worry about hitting the velocity wall or using unsafe loads. This guide clears up the physics, gives you safe load-building steps, and points out the mistakes that ruin subsonic accuracy or safety.
In short: Hunting with subsonic .308 Winchester ammo is possible but highly restricted. It requires a bullet designed to expand at very low velocities, a chamber with minimal freebore, and a load that reliably passes a safe threshold. Standard full-power hunting bullets will not work; you must use specialized subsonic projectiles to maintain ethical energy at the target.
Quick picks
Our shortlist for this job · tap one to see today's priceControls shoulder and neck size precisely, which is critical when pushing heavy subsonic bullets to the front.
Verifies case length and headspace so you do not push rounds too far into the chamber during subsonic loading.
What subsonic .308 ammo actually is
Subsonic means the bullet travels below the speed of sound, roughly 1,000 to 1,125 fps depending on temperature. For the detail, see our notes on choosing a reliable guide.
In a .308 Winchester, this usually means firing a 250- to 250-grain bullet with a very light powder charge.
You are not just slowing down; you are changing the entire pressure curve.
The case must burn completely at a slower rate to avoid a pressure spike at the chamber head. This is different from a normal varmint load; it is a distinct reloading discipline.
The bullet must be long enough to engage the rifling fully.
In a .308, the chamber is relatively long, so the bullet must be seated deep enough to stay inside the case body or just at the shoulder. If it sits too far out, it is not subsonic in the barrel, it is transonic and dangerous.
- Hornady Comparator Body – The Hornady Lock-N-Load Bullet Comparator is perfect for the
- Why Do You Need a Hornady Bullet Comparator – Measuring cartridge lengths across the
How subsonic loads work in a .308
The key is the pressure curve. You use a light charge of slow-burning powder, often a subsonic-specific load data entry from a manual.
The goal is to reach peak pressure slowly, allowing the bullet to accelerate past the muzzle before the pressure is at its maximum. We go through die durability tradeoffs step by step in its own article.
Seating depth is everything. For subsonic .308, you typically seat the bullet to the case body or just under the shoulder.
This moves the powder space out and helps the pressure curve. If you seat it to the neck, you are not subsonic; you are just a light charge with a long bullet, which can be dangerous.
Use a reloading gauge to check your final length.
The gauge ensures the case head is flush with the back of the gauge, meaning you have not pushed the case into the chamber too far. This is a critical safety check for every lot.
Confirms the case head is flush, preventing over-pressurization during subsonic loading.
- Hornady Reloading Equipment - constructed of carbon steel, this Hornady Lock n Load
- Easy to Use - simply insert the cartridge into the gauge and seeing if the head of the
When subsonic .308 is actually useful
This is not for elk or deer.
Subsonic .308 is for close-range varmint (crows, groundhogs, maybe a very close coyote) or ethically hunting very small game (rabbits, squirrels) where noise discipline is the priority, not range.
If you are hunting in a sensitive area where a loud report spooks game or disturbs neighbors, this load gives you a quiet shot.
However, you must be at the range where the bullet still has enough energy to take down the animal instantly. For most .308 rifles, that range is short, often under 100 yards. For the detail, see our notes on installing rcbs reloading tools.
Do not use this load for long-range hunting. Subsonic bullets drop like stones.
You need a scope with low magnification and holdover marks, not a high-powered glass. The bullet will not recover energy; it will just keep losing it.
Common mistakes and myths that ruin subsonic loads
Myth: “I can use a standard .308 bullet with less powder to make it subsonic.”
Fact: No. Standard bullets are designed to expand at higher velocities. At subsonic speeds, they may not expand at all, passing through the animal without killing it. You must use a bullet specifically designed for subsonic expansion.
Myth: “I can just guess the powder charge.”
Fact: Subsonic loads are on the edge of the pressure curve. A small change in powder weight or bullet seating can push the pressure into a dangerous zone.
You must start with published data and work up slowly.
Myth: “Subsonic means safer, so I can ignore headspace.”
Fact: The low pressure can hide a problem, but if the case is oversized, it will still fail. Always check headspace with a gauge.
A bullet puller is also useful if you need to recover a bullet for inspection or to test a new seating depth.
Allows you to recover bullets to inspect seating depth or check for lead fouling in the chamber.
- Includes Bullet Puller Collet
- For Use With .308 Bullet Diameters
How to build a safe subsonic .308 load
Step 1: Get the right bullet. Look for 250-grain or heavier subsonic-specific bullets.
Step 2: Prepare your dies. Use a 2-die set to control the shoulder and neck. This is where you get the consistency needed for accuracy. A full-length sizer with a zip spindle helps eliminate the “zip effect” that can cause pressure spikes.
Step 3: Check your gauge. Before loading, run a case through your cartridge gauge. It must be flush. If it is tight, you are pushing the case too far. Back it off.
Step 4: Follow the manual. Start with the minimum recommended charge for subsonic. Do not add powder until you are sure the bullet is exiting the muzzle subsonic. Use a chronograph if you can.
Step 5: Shoot and inspect. Check the primer for signs of excessive pressure. If the primer is bulging or the case is dark, back off. Subsonic loads are forgiving only if you stay within the data.
The bottom line
If you are hunting varmint in a noise-sensitive area, a subsonic .308 load built with a 2-die set and a bullet puller for recovery is a valid, safe option. Do not use it for big game. Start with published subsonic data, check your headspace with a gauge, and use a scope with low magnification.
- Hornady Reloading Equipment - constructed of carbon steel, this Hornady Lock n Load
- Easy to Use - simply insert the cartridge into the gauge and seeing if the head of the
Frequently asked questions
Can I use standard .308 hunting bullets subsonic?
No. Standard bullets like the Hornady InterLock or Nosler Partition are designed to expand at higher velocities. At subsonic speeds, they will not expand, leading to a non-lethal shot. You must use a bullet specifically designed for subsonic use, such as a heavy FTX or a dedicated subsonic projectile.
What powder do I use for subsonic .308?
You need a slow-burning powder that produces a flat pressure curve. Common choices include H110, Reloder 15, or subsonic-specific powders. Check the current load data from your powder manufacturer for the specific bullet weight and seating depth. Never guess.
Is subsonic .308 legal for hunting deer?
No. In most jurisdictions, subsonic loads do not meet the minimum energy requirements for big-game hunting. It is illegal for deer, elk, or bear. It is only suitable for varmint or very small game where local laws permit. Always check your state or country regulations before using it for hunting.
How accurate is subsonic .308 ammo?
It is less accurate than standard loads due to slower pressure and less consistent bullet exit. However, with careful case prep and a 2-die set, you can group 3-4 inches at 100 yards. Do not expect rifle accuracy. It is good for close-range shots only.



