Skip to content

RCBS Turret Press Ram: What It Is and How to Fix Issues

By Published 5 min read

As an Amazon Associate we earn from qualifying purchases, at no cost to you.

On this page (7 sections)
  1. What the ram actually does in a turret press
  2. How ram and turret alignment affects accuracy
  3. Common ram issues and how to fix them
  4. Choosing the right turret press for your setup
  5. Maintenance tips to keep your ram running true
  6. The bottom line
  7. Frequently asked questions

You are struggling with case alignment or seeing inconsistent bullet seating depths on your RCBS turret press. This page explains exactly what the ram does, how it interacts with the turret, and how to ensure it is set up correctly.

In short: The ram is the vertical piston that drives the case up into the die set for resizing, priming, and seating. It does not rotate with the turret; instead, it passes through the center hole of the turret head while the turret swings over it. Proper function depends on the ram moving smoothly and staying perfectly vertical to ensure concentric case alignment.

Quick picks

Our shortlist for this job · tap one to see today's price
Best all-around RCBS turretRCBS 6-Station Turret Reloading Press

Cast iron frame and detent system keep the ram and turret aligned under heavy load.

Check price on Amazon
Upgrade for multi-caliber shootersRCBS Turret Head

Allows you to swap turret heads quickly while keeping the same press body and ram.

Check price on Amazon

What the ram actually does in a turret press

RCBS Turret Press Ram: What It Is and How to Fix Issues

The ram is the central vertical component of the press. It moves up and down inside the press body to perform the five stages of reloading: deprime, resize, decap, powder, and prime/bullet. We cover rcbs turret press pros in a guide of its own.

Unlike a single-stage press where the ram stays fixed relative to the dies, a turret press has a rotating head that holds multiple dies. The ram passes through the center of this rotating turret. As you turn the handle, the turret swings over the stationary or moving ram.

This design allows you to change caliber by simply swapping the turret head or by using a turret with dies set up for different stages. The ram itself remains the same core mechanism that drives the case upward into the active die.

Recommended for this stepRCBS 6-Station Turret Reloading Press

The cast iron build ensures the ram channel stays true and does not flex under the pressure of reloading hard cases.

  • Run it one case at a time or keep dies set up on the turret.
  • Heavy frame and turret head stay solid under load.
Check price on Amazon

How ram and turret alignment affects accuracy

Precision shooting depends on the case being centered on the ram. If the turret is not aligned correctly, the case will be off-center when it enters the die, causing the bullet to seat at an angle or the case to expand unevenly.

RCBS turret presses use a detent system to hold the turret in place. This detent locks the turret so it does not drift while you are operating the press. However, the ram must still be perfectly vertical relative to the turret hole.

If the ram is bent or the press body is out of square, you will see poor concentricity. This is why heavy cast iron frames are preferred for turret presses; they resist the twisting forces that can occur when you are cycling a stiff case through the resize die.

Pro tip: Check the vertical alignment of the ram by looking through the top of the press body at the die hole. The hole should be a perfect circle, not an oval. An oval indicates the ram channel is misaligned. The other half of this decision is rcbs press performance check.

Common ram issues and how to fix them

The most common complaint about RCBS turret presses is the ram becoming stiff or sticky. This usually happens when powder residue or case lube gets into the guide bushings that hold the ram.

Another issue is the ram not reaching the top of its travel. This can happen if the lock ring is tightened too much or if the turret head is not seated properly on the ram.

  • Sticky Ram: Disassemble the press head, clean the guide bushings with a clean rag, and apply a small amount of press oil. Never use WD-40 as a lubricant; it is a solvent that dries out quickly.
  • Short Travel: Loosen the lock ring on the turret head by one to two degrees. Ensure the head is fully seated on the ram before tightening.
  • Jammed Turret: Check for a case crimped onto the die. Back the turret off carefully and remove the case.
Recommended for this stepRCBS Turret Head

If your ram mechanism is intact but you are changing calibers frequently, a separate turret head saves you from recalibrating the press for every load.

  • RCBS Turret Head: Additional turret head for RCBS Turret Press, enabling quick die
  • Quick Die Changes: Easily replace dies with this turret head, enabling faster
Check price on Amazon

Choosing the right turret press for your setup

When looking at the RCBS Rock Chucker Supreme or similar models, pay attention to the material of the frame. Cast iron is heavier but more stable. Aluminum frames are lighter but can flex more under the stress of reloading.

For competition shooting where every ounce of accuracy counts, the weight of a cast iron frame helps keep the ram stable. The detent system on RCBS presses is a key feature; it ensures the turret stops exactly where it should, which is critical for consistent die engagement.

Do not confuse the ram with the turret. The ram is the moving part; the turret is the rotating part. Both must work in harmony. If one is worn or out of adjustment, the other will suffer.

Safety first: Never force the handle if the press feels stuck. Stop, check the die, and ensure no case is jammed. Forcing the ram can bend it, which ruins the press. Before you buy anything, it is worth looking at buying an rcbs turret press.

Maintenance tips to keep your ram running true

Maintenance tips to keep your ram running true

Regular maintenance is the only way to keep the ram moving smoothly. After every reloading session, wipe down the ram and the turret area with a dry cloth to remove case lube.

Once a month, apply a drop of oil to the guide areas. Check the detent pins for wear; if the turret swings on its own, the detents may be worn out and need replacing.

Store the press with the turret locked in the first position. This relieves any tension on the spring mechanisms that hold the turret in place.

The bottom line

The ram is the heart of your RCBS turret press. If you are experiencing alignment issues or stiffness, clean and lubricate the guide bushings first. For most shooters, the RCBS 6-Station Turret Press is the best balance of stability and usability. If you change calibers often, consider an additional turret head to save setup time.

Our top pickRCBS 6-Station Turret Reloading Press
  • Run it one case at a time or keep dies set up on the turret.
  • Heavy frame and turret head stay solid under load.
Check price on Amazon

Frequently asked questions

Can I replace just the ram on an RCBS turret press?

The ram is typically part of the main press body assembly and is not sold as a standalone replacement part for most models. If the ram is bent or broken, the entire press head usually needs to be replaced or sent for professional repair.

What is the difference between the RCBS Rebel and Rock Chucker Supreme ram?

The RCBS Rebel is an entry-level turret press, while the Rock Chucker Supreme is a single-stage press that can be converted to turret use. The Rebel has a turret built into the design, whereas the Supreme uses a separate turret head that mounts onto the ram. The Supreme’s cast iron frame is generally more rigid for precision work.

How do I know if my turret is aligned correctly with the ram?

Visual inspection is the best test. Look through the top of the press at the die opening. The hole should be a perfect circle. If it looks oval, the turret is not aligned. Use a dial indicator for precise measurement if available.

Does the ram on a RCBS press need to be lubricated?

Yes, the guide bushings that the ram moves through should be kept lightly oiled. However, do not get oil on the case lube or the dies, as this can affect powder ignition and bullet performance.