Lee Precision Load Master Progressive Press Explained
By Amis Thains Updated 5 min read
As an Amazon Associate we earn from qualifying purchases, at no cost to you.
On this page (7 sections)
You want to load 9mm or .40 S&W quickly without juggling five different stations. This page breaks down exactly what the Lee Load Master Progressive Press does, who it fits, and what to check before you pull the trigger.
In short: The Lee Precision Load Master is a progressive press that seats, primes, and resizes in one continuous cycle, which cuts down the number of tool changes compared to single-stage or two-stage presses.
It works well for high-volume pistol ammo, but it requires more upfront setup and die knowledge than a simple single-stage machine. Read on to see if it matches your reloading goals. We cover hand press review in a guide of its own.
Quick picks
Our shortlist for this job · tap one to see today's priceAutomates multiple stages in one stroke, cutting reload time for frequent 9mm or .40 S&W loaders.
The Lead Sizing Die Kit shapes cast or gas-check bullets to spec, a required step before they fit into your case.
Who it is for (and who should skip it)
The Load Master earns its space if you load a high number of handgun cartridges each month. It shines for pistol ammo in standard cases like 9mm, .40 S&W, and .45 ACP. For the detail, see our notes on lee 223 reloading kit review.
You should skip it if you only load a few hundred rounds a year. For low-volume work, the setup and die alignment required by a progressive press cost more time than they save.
It is also not the right tool if you reload large rifle cartridges that need complex, multiple die stages beyond what the press’s station count supports. Check the current Lee specification sheet for the exact station and case-length limits before buying.
Pro tip: Always cross-reference your bullet and powder combination against a published reloading manual. A fast press does not justify skipping the load data.
What stands out about the design
The defining feature is the multi-station turret. One pull of the handle runs the case through the resizing, priming, and bullet-seating dies in sequence.
- Continuous cycle: Unlike a single-stage press where you move each case to a new die, the case stays in the shell holder and advances automatically.
- Built-in alignment: The machined body holds the die stations in a fixed, precise alignment, which reduces the guesswork of die height compared to some entry-level progressives.
- Compact footprint: It is smaller and lighter than many four-station progressive presses, making it a better fit for a small reloading bench.
This mechanical simplicity means fewer adjustments to dial in, which lowers the learning curve for shooters coming from a single-stage hand press.
The drawbacks to expect
The fast speed of a progressive press hides its flaws. If your dies are not set up perfectly, you will produce a large batch of bad ammo quickly. We cover lee pro 1000 rcbs counterpart in a guide of its own.
- Die sensitivity: Progressive presses are less forgiving of die height errors than single-stage presses. A half-millimeter off can cause case crimping issues or improper bullet seating.
- Case prep is critical: You must decap and size your cases in a separate single-stage press before they enter the Load Master. Feeding a loaded, un-decapped case into a progressive station will jam the mechanism.
- Primer feed reliability: The auto-primer feed mechanism can stall or feed primers at an angle if it is not kept clean and well-oiled.
Common owner experience shows that the first two or three batches are usually about figuring out the dial-in. Patience during setup prevents the frustration of a bad reload.
If you cast your own 9mm bullets, the 90601 Lead Sizing Kit is the exact tool you need to prep them to the correct diameter before they reach the seater.
- Machined aluminum mold Blocks and hard anodized sprue plate
- Tangential cut off which helps to eliminate the nip at the sprue cut off
Setup and use tips for a clean first batch
Follow this order to get consistent results on your first run. Skipping steps is the most common cause of jams and bad ammo.
- Prepare your cases first. Decap and resize all cases on a single-stage press. The Load Master is not a decapping tool.
- Set the seater depth. Dial the bullet seater die until the bullet is seated to the exact specification found in your reloading manual. Do a test string on scrap cases before you prime and seat live rounds.
- Load the primer feed. Drop one primer into the feed tube to verify the feed dog grabs it and drops it perfectly square into the flash hole.
- Run 10 rounds first. Pull a small batch and inspect every round for seating depth and primer alignment. Make any micro-adjustments now, not after you have loaded a whole box.
Safety first: Check the seated bullet depth of every round in a test batch. A short or over-seated bullet is a safety hazard and must be identified before firing.
Alternatives worth a look
If the Load Master’s price or setup requirement does not fit your workflow, here are two other tools that solve the same problems differently.
For low-volume, fast handgun reloading
The Lee Pacesetter die set pairs with a basic single-stage press to give you a complete 9mm reloading setup without the complexity of a progressive system.
For dedicated 9mm bullet prep
The Lee Precision 90601 Lead Sizing Die Kit is the correct tool if you are casting 9mm bullets and need to shape them to the exact .450 or .451 diameter specification. Loaders in this spot often ask about comparing 9mm tooling as well.
The bottom line
The Lee Load Master Progressive Press is the right choice for high-volume pistol reloaders who want to cut down the time spent at the bench. It demands a bit of upfront setup, but the payoff is speed and consistency for standard handgun ammo. If you buy it, get a quality single-stage press for case prep, and always verify your seating depth on a test batch before reloading a full box.
- Product Type: Sporting Goods
- Package Dimensions: 8.89 L X 7.111 W X 1.27 H (Cm)
Frequently asked questions
Can I use the Lee Load Master for rifle cartridges?
Not typically. The Load Master is designed for small-diameter, short-case handgun cartridges. Its station layout and feed mechanism are optimized for pistol ammo. If you load a wide variety of rifle calibers, a versatile four-station progressive press is a better fit.
Does the Load Master come with dies for every cartridge?
The base press does not come with a universal die set. You must buy or build the specific die sets for each cartridge you load. Lee sells dedicated 9mm and .40 S&W die sets, but you need to purchase them separately or use existing Pacesetter dies.
How many rounds per hour can I expect to reload?
Once fully dialed in, most shooters report reloading 9mm at a pace of 300 to 500 rounds per hour. Your actual speed depends on your bullet prep workflow and how quickly you can clear the completed cases from the station.
Do I need to decap my cases before using the progressive press?
Yes. You must fully decap and resize your cases on a single-stage press before you put them in the Load Master. Feeding a case that still has a spent primer in the flash hole will jam the press and damage your equipment.

