Hornady Lock-N-Load Powder Measure Review & Test
By Amis Thains Updated 6 min read
As an Amazon Associate we earn from qualifying purchases, at no cost to you.
On this page (7 sections)
You need consistent powder charges but want to avoid the cost of a digital dispenser. This page breaks down the Hornady Lock-N-Load Bench Rest measure's real-world accuracy and setup quirics.
In short: The Hornady Lock-N-Load Bench Rest is a reliable mechanical measure for high-volume loading. It works best with flake and ball powders when you use a consistent throw. You should skip it if you load small pistol charges below 20 grains or need digital-level precision.
Quick picks
Our shortlist for this job · tap one to see today's priceHandles 20-65 grain charges with simple micrometer adjustments, ideal for standard rifle and large pistol loads.
Offers 0.5cc capacity for accurate sub-20 grain charges that the Hornady measure cannot handle.
Catches manual errors with a scale that reads to 0.1 grain, essential for checking your measure's consistency.
Who it is for (and who should skip it)
The Hornady Lock-N-Load Bench Rest measure is a mechanical tool. It throws charges between 20 and 65 grains. If you reload standard rifle cartridges or large-frame pistols, this range covers your needs perfectly. Most .308 Win, .308 Win, 7.62×39, and .458 Win Mag loads fall squarely in this sweet spot. The other half of this decision is arsenal x-10 reloading kit.
If you load sub-20 grain pistol loads, this measure will not work. You need a dedicated pistol measure with a smaller cup capacity. The 3DEXL Pistol Powder Measure mentioned below fills that gap with a 0.5cc cup, which is suitable for 9mm and .45 ACP.
It suits high-volume shooters who want consistency without digital complexity. It is not the right tool for competitive long-range shooters who require sub-0.1 grain precision from a manual device. For those shooters, a digital dispenser is a better investment despite the higher cost.
Pro tip: Check your powder charge weight. If it is under 20 grains, you need a different measure.
This is the main product being reviewed, suitable for most rifle and large pistol loaders.
- Promotes uniform filling
- Micrometer adjustment
What stands out in daily use
The micrometer adjustment is the standout feature. You can fine-tune the charge weight without turning the knob hundreds of times. One click of the micrometer makes a small, predictable change. This allows you to dial in your target weight quickly without guessing or wasting powder.
Owners report that the hopper design prevents bridging with most flake powders. The wide funnel makes pouring powder easy, even with static-prone brands. The base is heavy enough to stay put on a standard reloading bench. It does not slide around when you pull the lever aggressively, which helps maintain consistency.
It is simpler than digital dispensers. There are no batteries to replace or calibration files to manage. You just pull the lever and the charge lands in the cup. This simplicity means fewer things can break. If you lose the lever spring, it is a common part, not a proprietary electronic component that requires a service visit. For the detail, see our notes on confirming scope durability.
Pro tip: Use a dry cloth to wipe the hopper and drop tube before switching powder types.
The drawbacks you must know
Manual measures are only as consistent as your technique. If you pull the lever softly on some shots and hard on others, the charge weight will vary. Practice makes a difference. A rushed throw often results in a lighter charge because the powder does not settle into the metering cylinder completely before the gate closes.
Static electricity is the main enemy. Powder clinging to the plastic hopper walls reduces the weight of the charge. This happens more often with certain extruded powders. You must verify your weights on a scale regularly. Static buildup is worse in dry climates, so consider using anti-static spray or a humidifier if you are reloading in winter.
The 20-grain minimum is a hard limit. You cannot calibrate it for lighter loads. If you shoot .22 LR or small pistol cartridges exclusively, this tool is useless to you. The metering cylinder is simply too large to hold a reliable 5-gram charge without bridging or clogging.
Safety first: Always verify your charge weight with a digital scale before loading a batch of cartridges.
Setup and use tips for accuracy
Start with a clean hopper and drop tube. Pour in a small amount of the powder you intend to use. Let it settle for a few minutes to ensure a consistent density. If the powder is freshly disturbed, it will meter differently than settled powder. For the detail, see our notes on lock and load powder.
- Set the micrometer to the midpoint of your desired charge.
- Throw 5-10 test charges into a scale.
- Weigh each charge and calculate the average.
- Adjust the micrometer up or down based on the difference.
- Repeat until the average weight matches your load data.
- Throw another 5 charges to confirm the new setting is stable.
Keep your lever pull smooth. Do not jerk the handle. A consistent stroke is the key to consistent weight.
Use the same pour of powder for all your test charges to avoid density changes. Mark your hopper with a piece of tape so you always pour to the same level, ensuring the volume of powder available is constant for every session.
You need a reliable digital scale to verify the manual measure's output during setup.
- PRECISION RELOADING SCALE WITH ±0.1 GRAIN ACCURACY: Achieve competition-level
- AUTOMATIC POWDER DISPENSER WITH FAST 2 GRAIN/SECOND SPEED: Say goodbye to tedious
Alternatives worth a look
If the 20-grain limit blocks you, the 3DEXL Pistol Powder Measure is the direct alternative. It handles charges down to 0.5cc, making it perfect for 9mm and .45 ACP.
This kit includes various scoops and a dipper, which gives you flexibility for different load types without buying multiple measures. It is a budget-friendly option for hand-loaders who want to cover a wide range of calibers.
If you want to eliminate operator error entirely, look at the Reloading Basic Digital Powder Scale. It dispenses and weighs the charge automatically. It is slower than a manual measure but much more precise for low-volume precision work.
The anti-static technology in these digital units helps prevent the powder from sticking to the internal components, which improves reliability over time. The speed is roughly 2 grains per second, which is manageable for working up a load. We go through assessing value for money step by step in its own article.
The Hornady measure remains the best value for high-volume rifle work where 0.1 grain accuracy is not critical, but consistency is. It is the workhorse of the bench for many shooters who produce hundreds of rounds at a time.
This alternative solves the problem of loading light pistol charges that the Hornady measure cannot handle.
- Wide measurement range from 0.5cc to 4.3cc for precise powder charges.
- Includes a variety of scoops and a dedicated powder dipper for quick setup.
The bottom line
Get the Hornady Lock-N-Load Bench Rest measure if you reload rifle or large pistol cartridges in volume. It is a robust, mechanical tool that rewards good technique. If you load light pistol charges, skip it and buy a dedicated pistol measure instead.
- Promotes uniform filling
- Micrometer adjustment
Frequently asked questions
Can I use the Hornady Lock-N-Load for pistol reloads?
Only for large-frame pistols with charges over 20 grains. For 9mm, .45 ACP, or other standard pistols, you need a measure with a smaller cup capacity, like the 3DEXL kit.
How accurate is the Hornady powder measure?
Accuracy depends on your technique and powder. With a smooth pull and clean equipment, you can expect consistency within a few hundredths of a grain. You must verify with a scale.
Why is my powder measure throwing light charges?
Check for static cling on the hopper walls. Ensure your lever pull is consistent. Also, verify that your powder has not changed density; flake powders can settle and measure differently than fresh lots.
Do I need a digital scale with a manual measure?
Yes. A manual measure is a dispense tool, not a weighing tool. You need a digital scale to confirm that your set charge weight matches your load data safely.
How do I recalibrate the Hornady powder measure?
There is no electronic calibration for this manual measure. You ‘calibrate’ it by adjusting the micrometer. Throw a series of charges, weigh them, and adjust the micrometer until the average matches your target. Repeat this process every time you switch powders.


