RCBS Partner vs Lee Press: Size & Compatibility Comparison
By Amis Thains Updated 6 min read
As an Amazon Associate we earn from qualifying purchases, at no cost to you.
On this page (8 sections)
You are deciding between two compact reloading presses but cannot tell how much desk space they need or if the Lee dies will fit the RCBS frame. This page gives you the exact dimensions, frame types, and compatibility facts to make the call.
In short: The RCBS Partner is a small, single-stage press meant for pistol calibers like 9mm, while the Lee 90045 is a mid-size single-stage press for rifle and pistol reloading. Both use standard 7/8-14 die threads, so Lee dies physically fit the RCBS Partner, but you lose the quick-change bushing system. The Partner saves bench space; the Lee 90045 handles heavier rifle loads.
Quick picks
Our shortlist for this job · tap one to see today's priceCompact aluminum frame saves space, perfect for 9mm and pistol reloading in tight setups.
Heavier steel frame handles larger calibers and provides more stability for rifle shots.
What are you actually comparing: a press vs. a die set
The old title confused a 9mm die set with a press. You cannot run a die set without a press frame. This comparison assumes you are choosing the hardware that applies force for your bench. For the detail, see our notes on assessing special 5 value.
If you already own a press and need 9mm dies, skip ahead to the compatibility section. If you are building from zero, you need both the press and the dies to start reloading.
The search terms often mix up these two components. A press is the static frame that holds the dies and applies force via a lever. Dies are the precision tools that size, expand, and seat the cartridge.
Understanding this distinction is crucial because the ‘size’ you are looking for involves two different dimensions: the physical footprint of the press on your bench, and the compatibility of the die threads with that press.
Pro tip: A die set alone does nothing. You must match the die thread to the press you own or plan to buy.
RCBS Partner footprint and frame limits
The RCBS Partner is built from aluminum, which keeps it light and small. It measures roughly 10.5 inches wide and 8 inches deep at the base.
This makes it ideal for a small workbench or a garage corner where a full-size Rock Chucker would not fit. However, the lighter frame flexes more under heavy rifle pressures, so it is designed primarily for pistol calibers. Loaders in this spot often ask about choosing rcbs for 6.5 creedmoor as well.
Specifically, the Partner uses a C-frame design that places the operator on the right side. This ergonomic choice allows for a smaller lateral footprint compared to top-mounted die presses.
When you add the shell holder and a stack of cases, you need about 15 inches of clear working space in front of the press. If your bench is narrow, this compact width is the main advantage over the heavier Lee models.
The aluminum construction also means it is easier to move if you reload in multiple locations, such as a home shop and a range bench.
Pro tip: Leave at least 12 inches of clearance around the Partner's footprint for shell holders and die storage.
Its compact aluminum body is the main reason to buy it over a heavier press when space is tight.
- RCBS Partner Press: Compact, lightweight single-stage press ideal for beginners or
- Durable Aluminum Construction: Features a sturdy aluminum frame, ensuring long-lasting
Lee 90045 size and why it is bigger
The Lee 90045 is a single-stage press with a heavier cast steel frame. It is taller and deeper than the RCBS Partner, typically requiring about 14 inches of bench width.
The extra weight and steel construction reduce die drop under heavy loads, which is critical for rifle calibers like .308 Win or .223 Rem. If you are reloading 9mm only, the extra size is not necessary, but it provides a stable platform for future upgrades. There is more on comparing rcbs and lee presses in a separate guide.
The Lee 90045 utilizes the Breech Lock system, which adds a vertical height dimension to the die area. This means the top of your die stack sits higher above the bench surface than on a standard threaded press.
You must ensure your shell holder and case feeder can accommodate this increased height. The heavier steel base also provides better damping when seating heavy bullets for rifle cartridges.
For a user planning to move from pistol to rifle reloading, this extra bulk buys you long-term stability that the lighter Partner lacks.
The heavier frame stabilizes bullet seating for rifle loads that the lighter Partner may struggle with.
- Reloading Press
Will Lee dies fit the RCBS Partner?
Yes. Both the Lee 90045 and the RCBS Partner use the industry-standard 7/8-14 TPI die thread. Any Lee die set will screw directly into the RCBS Partner without adapters.
However, the Lee Breech Lock quick-change system will not work on the Partner unless you buy aftermarket RCBS-specific bushings. You will lose the ability to swap dies without readjusting them. For a 9mm-only setup, this is not a major issue.
When using Lee dies on the RCBS Partner, you are relying on the threaded hole. The dies sit lower in the body of the press compared to the Breech Lock system on a Lee press. This changes the height of your shell holder. For the detail, see our notes on press comparison.
You may need to adjust your shell holder so the case contacts the base plate and the bullet seats correctly.
The physical fit is secure, but the operational workflow is slower because you must twist the dies manually for every changeover, rather than pulling a lock ring.
Safety first: Always hand-tighten dies until they contact the press body, then tighten with a wrench. Over-tightening can strip the thread.
If you want to keep quick-change capability on the Partner, these bushings are the only way to add it.
- Has an all steel linkage with adjustable length lever
- One Breech Lock quick change bushing also included
Common myths about press size and accuracy
Myth: A smaller press is less accurate for 9mm.
Fact: The RCBS Partner is fully capable of consistent 9mm reloading. Accuracy depends on die quality and your technique, not the press brand or size.
Myth: You need a heavy press for rifle calibers.
Fact: The lighter Partner can handle .223 Rem, but you will feel more die drop under heavy crimping. The Lee 90045 is the safer choice if you plan to reload .308 Win or magnum loads regularly.
Myth: Aluminum frames break easily.
Fact: The RCBS Partner uses reinforced aluminum. It is not brittle. It is a durable tool that has been used by thousands of shooters. The ‘flex’ concern is about die drop and spring-back under extreme pressure, not the frame snapping. For pistol calibers, the aluminum frame is structurally sound and accurate. Loaders in this spot often ask about swarm and pr magnum differences as well.
Which press should you buy first
If your bench is under 24 inches wide and you are reloading 9mm or small pistol calibers, the RCBS Partner is the better fit. It saves space and costs less.
If you want to reload rifle cartridges or expect to move up to heavier loads, the Lee 90045 gives you the extra stability and headroom. You can start with 9mm dies on the Lee and add rifle dies later without changing presses.
Consider your next step. If you are buying a press for the first time, the RCBS Partner is the simplest entry point. It is lighter to mount and easier to store.
If you are upgrading from a die set to a full press, and you already have Lee dies, the Lee 90045 is the natural home for them. Matching the press to your existing die investment saves money in the long run.
The bottom line
Buy the RCBS Partner if your bench is tight and you are staying in pistol territory. Buy the Lee 90045 if you want one press that handles both 9mm and rifle calibers without swapping hardware. Most beginners should start with the press that fits their calibers, then add the matching die set.
- RCBS Partner Press: Compact, lightweight single-stage press ideal for beginners or
- Durable Aluminum Construction: Features a sturdy aluminum frame, ensuring long-lasting
Frequently asked questions
Can I use Lee 9mm dies on an RCBS Partner press?
Yes. Both use the standard 7/8-14 die thread. The Lee dies will screw in and function perfectly. You will not be able to use the Lee Breech Lock quick-change system unless you buy aftermarket bushings.
Is the RCBS Partner too small for rifle reloading?
It can reload .223 Rem, but the lighter aluminum frame flexes more under heavy loads. If you plan to shoot .308 Win or magnum calibers, the Lee 90045 or a Rock Chucker is a better choice.
Which press takes up less bench space?
The RCBS Partner is about 10.5 inches wide. The Lee 90045 is closer to 14 inches wide. Measure your bench before buying, as shell holders and die cases need room around the press.
Do I need a press before I buy dies?
Yes. A die set is useless without a press to screw into. Decide which press fits your bench and calibers first, then buy the die set that matches the thread and quick-change system of that press.


