How Long Should I Run My Hornady Case Dryer?
By Amis Thains Published 5 min read
As an Amazon Associate we earn from qualifying purchases, at no cost to you.
On this page (7 sections)
You just pulled clean brass from a tumbler or ultrasonic, but it is still damp, and you are worried about starting your next case getting streaks or rust. This page gives you the specific run times for Hornady dryers and the variables that change how long you need to run them.
In short: Most Hornady case dryers need 30 to 60 minutes to dry cases after ultrasonic cleaning. Tumbler-washed brass often needs 45 to 90 minutes because the media leaves more water. Always check the brass to ensure it is fully dry before storing to prevent rust.
Our pick
Tap to see today's price on AmazonHolds up to 2,000 9mm cases and dries them in 1-2 hours.
Standard run times for Hornady case dryers
Most Hornady case dryers operate on a simple heat system that evaporates moisture from brass. There is no universal timer, so you manage the duration manually. Before you buy anything, it is worth looking at patches for 9mm.
For ultrasonic-cleaned cases, 30 to 45 minutes is usually enough. These cases leave the machine with surface water, which evaporates quickly under gentle heat.
For rotary tumbler cases, plan for 45 to 90 minutes. Tumbling media holds water in its texture, which takes longer to release under heat than plain ultrasonic solvent.
Start with 30 minutes. Open the door and touch the brass with your fingertip. It should feel dry and neutral temperature, not cold or damp.
If you are using a larger capacity dryer, such as the 2-quart or 5-quart models, add 10 to 15 minutes to these times. The extra volume slows air circulation, so the moisture takes longer to escape.
Consistency is key. Once you find the time that works for your specific washer and dryer combo, write it down. This prevents you from guessing every time you reload.
Pro tip: Do not set the timer and walk away. The final 10 minutes can make the difference between dry and slightly damp. Loaders in this spot often ask about hornady drying equipment as well.
- The perfect companion to any ultrasonic or rotary Tumbler Cleaning System
- Holds up to 1000- 223 cases or 2000 - 9mm cases
How load size and humidity change the clock
More cases mean more total moisture to evaporate. A half-full chamber dries faster than a full one because hot air circulates better.
Humidity in your workspace also plays a role. In a dry, heated garage or basement, 30 minutes may suffice. In a humid coastal home, you may need to add 15 minutes to the same load.
If you are running a high-capacity dryer like the Lyman Cyclone, the spec sheet suggests 1 to 2 hours for maximum loads. This aligns with the general rule: heavier loads require longer run times.
We recommend checking the manufacturer’s current manual for your specific Hornady model. Some older units have fixed cycles, while newer ones allow manual control.
A simple hygrometer on the wall of your reloading room tells you the moisture in the air. When relative humidity is above 70%, assume your cases will need the maximum recommended time. When it is below 40%, you can often shorten the cycle.
Temperature matters too. If your shop is cold in winter, the dryer has to work harder to heat the air. If it is hot in summer, the moisture evaporates faster. Adjust your timer based on the season. For the detail, see our notes on gun cleaning tool boxes.
Signs your cases are still wet
You do not need a scientific test to know if brass is dry. Look for these three visual cues.
- Fogging: If the interior of the dryer lid is fogged, moisture is still evaporating. The dryer is not done.
- Color shift: Dry brass is uniform. Wet brass looks darker or has water spots. If you see spots, keep running the dryer.
- Temperature check: Wait until the cases are warm to the touch. Cold cases are often still damp inside the metal.
If you close the dryer and open it 10 minutes later and the brass feels cold and slightly clammy, it was not done. Run it for another 20 minutes.
Check the primer pockets specifically. Water collects in the deep recess of the pocket and is the last to dry. If the pockets look dark, the case is not ready for storage.
Common mistakes that ruin drying
Myth: You can dry cases while they are warm from the tumbler. Fact: If cases are hot from cleaning, let them cool to room temperature first. Adding hot brass to a running dryer can spike the temperature and stress the metal.
Myth: Running it for 2 hours is safer than 30 minutes. Fact: Overheating can warp the plastic parts of your dryer and discolor the brass. Excessive heat is not better drying.
Myth: You can leave the dryer on all night. Fact: This wastes energy and is a fire risk. Never unattended for extended periods.
Stick to the 30-90 minute window. It is efficient and safe.
Another common error is not letting the air vents clear. If you keep the dryer in a tight cabinet, heat builds up. This overheats the unit and can shut it down early. Place it on a stable table with space around the back for airflow.
Using a dryer when you don't have one
If you do not own a dedicated case dryer, you have two solid alternatives.
- Air gun: Blow off loose water, then lay cases on a towel in a warm, dry room for 2 hours.
- Food dehydrator: Set to the lowest heat setting (often 100-125°F) for 30-45 minutes. This works well for small batches.
A dedicated dryer is more reliable and safer for long-term storage. If you reload more than 200 cases a month, the time saved is worth the investment.
The Lyman Cyclone is a popular choice in this space. It holds a large volume of cases and uses a fan system that cycles the warm air. For many shooters, it is the next step up from a simple heat lamp or food dehydrator. It provides consistent heat distribution, which is critical for preventing rust in high-volume loads.
A dedicated dryer that handles large batches of brass consistently, offering a reliable alternative to makeshift drying methods.
- The perfect companion to any ultrasonic or rotary Tumbler Cleaning System
- Holds up to 1000- 223 cases or 2000 - 9mm cases
The bottom line
Start with 30 minutes for ultrasonic-cleaned brass and 45 minutes for tumbler-cleaned brass. Open the door, check for fogging, and add time if needed. The Lyman Cyclone is a strong option if you are running high volumes and need a timer-based solution.
- The perfect companion to any ultrasonic or rotary Tumbler Cleaning System
- Holds up to 1000- 223 cases or 2000 - 9mm cases
Frequently asked questions
Can I put wet cases in the dryer?
Yes, but they should be at room temperature. If they are hot from cleaning, let them cool first. Pre-drying with a towel helps the dryer work more efficiently.
How do I know if my Hornady dryer is broken?
If the cases are still damp after 90 minutes, the heating element may be failing. Check the power connection and ensure the air vents are not blocked.
Does dryer heat change the brass?
No, not at normal operating temperatures (under 200°F). The heat is low enough to evaporate water without annealing or discoloring the brass.
