Skip to content

How to Set Up the Hornady Lock-N-Load AP Press for Single-Stage Reloading

By Published 6 min read

As an Amazon Associate we earn from qualifying purchases, at no cost to you.

On this page (8 sections)
  1. Tools and Supplies You Need Before You Start
  2. Step 1: Mount the Press and Prepare the Die
  3. Step 2: Install the Shell Holder and Case Feeder
  4. Step 3: Adjust the Case Gauge and Stop Pin
  5. Common Mistakes That Ruin Your Setup
  6. When to Upgrade to the Full Ammo Plant
  7. The bottom line
  8. Frequently asked questions

You just unboxed a Hornady AP Press and the manual’s instructions feel sparse, leaving you unsure if the die is seated correctly or the case feeder will jam. This guide walks you through the exact setup sequence for the AP platform, so you can get to your first test charge without guessing.

In short: Setting up a Hornady AP Press involves mounting the die, adjusting the case feeder for smooth loading, and verifying the stop pin alignment. The process is similar to a single-stage classic press but uses a shell holder for faster case handling. Follow the steps below to ensure reliable operation and accurate chambering depth.

Quick picks

Our shortlist for this job · tap one to see today's price
Best for most single-stage setupsHornady 085001 Lock-N-Load Classic Ammo Reloading Press

The classic single-stage base for the AP series; straightforward and reliable for beginners.

Check price on Amazon
Essential for die adjustmentDie Wrench Compatible with Hornady Press Systems

A dedicated wrench ensures proper die seating, which is critical for accuracy and safety.

Check price on Amazon
Best for high-volume productionHornady Lock-N-Load Ammo Plant

The full ammo plant kit if you plan to expand beyond basic single-stage work.

Check price on Amazon

Tools and Supplies You Need Before You Start

How to Set Up the Hornady Lock-N-Load AP Press for Single-Stage Reloading

Before touching the press, gather these items to avoid interruptions. A missing wrench or misaligned shell holder will stall your setup. For the detail, see our notes on prepping a hornady press for use.

  • Die wrench: Use a wrench compatible with Hornady flats (3/4 inch and 1/2 inch).
  • Shell holder: Specific to the AP press configuration.
  • Case gauge: For verifying headspace and chambering depth.
  • Primer catcher: Included with most Hornady presses to keep your bench clean.
  • Cleaning solvents: For die and case preparation.
  • Ball gauge: To verify crimp diameter consistency.

The die wrench is the most critical tool. Using a standard combination wrench can strip the die flats. P2 is a multi-functional wrench designed for Hornady systems, featuring the exact flats needed for die and spindle locks. Its compact design allows for tight spaces where the press body interferes with larger tools.

Recommended for this stepDie Wrench Compatible with Hornady Press Systems

Ensures secure die seating without stripping the press or die threads.

  • Versatile Reloading Tool: This multi-functional die wrench(396495) is designed to
  • Easy to Use and Compact: Featuring a handheld design with three precise flats (3/4 inch
Check price on Amazon

Step 1: Mount the Press and Prepare the Die

Step 1: Mount the Press and Prepare the Die

Start by securing the press to your bench. The base should be bolted down or weighted to prevent movement during operation. Vibration from the ram stroke can loosen components if the base is not stable.

  1. Loosen the die lock ring on the press.
  2. Insert the die into the body, ensuring it is vertical. Check the threads on the die shank for any debris.
  3. Tighten the lock ring firmly using the wrench.
  4. Do not fully seat the die yet; leave it slightly raised for case clearance.
  5. Rotate the die by hand to ensure no binding.

P3 is the standard base for this setup. It comes with primer catchers and die bushings, which help maintain consistency across different calibers. The included primer catcher prevents primers from scattering on your bench, saving cleanup time.

Recommended for this stepHornady 085001 Lock-N-Load Classic Ammo Reloading Press

Provides the stable single-stage platform required for the AP series.

  • Lnl classic loader
  • Each lock-n-load classic press Comes with primer catcher and three lock-n-load DIE
Check price on Amazon

Step 2: Install the Shell Holder and Case Feeder

The AP series often uses a shell holder to manage case extraction and insertion. This step determines your speed and smoothness. A misaligned holder will cause cases to hang up on the die lips.

  1. Attach the shell holder to the ejector pin. Ensure the pin is fully extended.
  2. Align the holder so the case sits flush in the die. The case should rest on the holder, not the die body.
  3. Ensure the holder does not interfere with the ram movement. The holder should move freely with the ram.
  4. Test the extraction by inserting a fired case and pulling it out manually.

If you are using a standard single-stage setup without a dedicated shell holder, use a manual case loader. The key is to ensure the case is seated fully before every stroke. Manual loading is slower but offers better control for complex cartridges.

Pro tip: Check that the shell holder is not touching the die body. Any contact causes wear and inconsistent case extraction. It helps to understand dialing in die setups for brass fit before going further.

Step 3: Adjust the Case Gauge and Stop Pin

This is the most critical step for accuracy. The stop pin and case gauge set your chambering depth. Incorrect settings can cause headspace issues, leading to case head separation in the chamber.

  1. Insert a clean, fired case into the die.
  2. Bring the ram up to the top of the stroke.
  3. Set the stop pin to the case’s maximum length for your chamber. Use a published chamber spec.
  4. Verify with a case gauge that the case does not protrude. The gauge should not fit into the chamber if the case is correctly seated.
  5. Adjust the die height if the case is not seating properly against the stop pin.

Never set the stop pin based on guesswork. Use a published chamber measurement for your specific rifle or handgun cartridge. For rifles, measure the free length of the chamber and set your stop pin slightly shorter than that length to ensure the case head is against the bolt face.

Safety first: Improper headspace adjustment can lead to overpressure and firearm damage. Always consult your rifle’s owner manual for chamber specs.

Common Mistakes That Ruin Your Setup

  • Mistake: Tightening the die too high.
    Fix: Leave a slight gap between the die and the shell holder. The case should be held by the holder, not the die. If the die is too high, it will scrape the case during extraction.
  • Mistake: Using the wrong wrench size.
    Fix: Use a wrench with correct flats to avoid rounding the lock ring. A rounded lock ring can slip during reloading, causing the die to spin.
  • Mistake: Forgetting to lubricate the case.
    Fix: Use a light lube on the case rim and body for smooth extraction. Without lube, the case will stick in the die, potentially causing a jam.
  • Mistake: Ignoring die alignment.
    Fix: Ensure the die is perfectly vertical before tightening. Use a level if necessary. A crooked die will produce crooked bullets, affecting accuracy.
Common Mistakes That Ruin Your Setup

Most of these mistakes are reversible, but a stripped lock ring or a cracked die body is not. Take the time to verify each adjustment before loading your first primer.

When to Upgrade to the Full Ammo Plant

If you find yourself reloading high volumes or want automated case feeding, the full Ammo Plant is the next step. It adds a case feeder and primer station for speed, reducing the number of manual operations per round.

P1 is the complete kit for those who want to maximize production. It includes the most intuitive reloading system for speed and performance. However, the basic AP setup is sufficient for most recreational reloaders who do not need to produce thousands of rounds per session. We go through using a trimmer for precision step by step in its own article.

The full plant requires more bench space and a sturdier workbench to handle the additional weight and vibration.

Recommended for this stepHornady Lock-N-Load Ammo Plant

Adds automated features for shooters who need high-volume production capability.

  • Hornady Lock-N-Load Ammo Plant – This kit represents the ultimate reloading setup for
  • Fast Reloading – Equipped with the most intuitive reloading system, the Hornady Ammo
Check price on Amazon

The bottom line

For most hand-loaders, the standard AP press setup with P3 and P2 is sufficient and reliable. Focus on precise stop pin adjustment to ensure safe headspace. If you plan to reload hundreds of rounds regularly, consider the full P1 kit for added speed.

Our top pickHornady 085001 Lock-N-Load Classic Ammo Reloading Press
  • Lnl classic loader
  • Each lock-n-load classic press Comes with primer catcher and three lock-n-load DIE
Check price on Amazon

Frequently asked questions

Is the Hornady AP Press the same as the Lock-N-Load Classic?

The AP series is part of the Lock-N-Load family but often refers to specific automatic or assisted platforms. The basic single-stage setup is very similar. Check the specific model number to confirm features, as the AP designation may indicate automatic case feeding or other automated components not found on the classic manual press.

How do I know if my die is set correctly?

Use a case gauge. The case should not touch the stop pin when fully seated. If it does, back the die out slightly. Always test chamber a bullet in a dummy round first to verify that the cartridge headspaces properly in your firearm without any binding.

Can I use a Lee or RCBS die with a Hornady press?

Yes, if the die has standard threaded shanks. However, the shell holder and stop pin systems are press-specific. You may need adapters or different tooling to ensure the die locks securely and the case aligns correctly with the holder.

What is the best wrench for Hornady presses?

A dedicated die wrench with 3/4 and 1/2 inch flats is best. Avoid using adjustable wrenches, which can slip and damage the die threads. A multi-functional wrench like P2 is ideal because it fits both the die flats and the spindle locks. It helps to understand 6.5 creedmoor bullet comparator before going further.